Clermont Pool Electrical Works logo Clermont Pool Electrical Works Pool Electrical Repair · Clermont, FL

2026-11-15 · Clermont Pool Electrical Works

Pool Equipment Lost Power After a Storm: What to Check

If your pool equipment lost power after a storm, start at the breaker panel and the GFCI, not at the pump. Most post-storm outages come from a tripped breaker or GFCI, water in an outdoor box, or a power surge that damaged a timer or control board. Work through the list below, and stop if you see water around the equipment or smell burning.

Safety first

  • If the equipment pad is flooded or standing in water, do not touch anything. Switch off the breakers from the main panel only if you can reach it dry.
  • If you see scorch marks, melted plastic or smell burning, leave the breaker off and call an electrician.
  • Never open a wet equipment box or stand in water while touching pool equipment.

Step 1: Check the main and pool breakers

Look at the panel for a breaker that sits between ON and OFF. To reset a tripped breaker, push it fully to OFF and then back to ON. If it trips again right away, stop. A breaker that will not stay on means a fault, and repeated resets only stress the circuit. Our page on a pool breaker that won't reset explains why.

Step 2: Check the GFCI

Many pool circuits are protected by a GFCI, either as a breaker in the panel or as a receptacle-style device near the equipment. Press the TEST and then RESET buttons. If it will not reset, or resets and trips again, moisture or damaged wiring is the likely cause. See pool GFCI keeps tripping.

Step 3: Look at the timer or automation panel

Lightning and surges often damage control boards, timers and transformers even when the pump motor is fine. If the pump runs when switched directly but not from the timer or automation panel, the control side has failed. Signs include a blank display, a clicking relay that never closes, or a timer that has lost its schedule. Our pages on timers that will not turn the pump on or off and on automation not controlling equipment cover these faults.

Step 4: Check for water and corrosion at the pad

Heavy rain can drive water into disconnect boxes, timer enclosures and conduit fittings. Look for water droplets, rust or green corrosion at terminals, and a musty smell. Do not wipe down or dry out live equipment. If you find water inside a box, turn off the breaker and have it inspected, because moisture left in a box often causes the next trip.

Step 5: Is it a power outage rather than a pool fault?

Check whether other circuits in the house are dead, and whether neighbors have power. If the whole street is dark, wait for the utility to restore service. Once power returns, a pump may need a manual restart, and timers may need resetting.

When to call a pool electrician

Call if a breaker or GFCI trips again after one reset, if any equipment shows water damage, if the pump hums but does not start, or if the timer or automation panel is dead. Our pool equipment lost power after rain or storm service covers diagnosis and repair of the circuit. Homeowners in Minneola and across Lake County call us after storm weeks.

For a related problem, see why a pool light trips the GFCI.

What the symptom points to

| What you see | Where to look first | |---|---| | Everything at the pad is dead | Main or pool breaker, GFCI, utility outage | | Pump runs, lights and controls dead | Control board, transformer, or a separate breaker | | Timer display blank or reset | Surge damage or loss of power to the timer | | Breaker trips immediately when reset | Water in a box, damaged wiring or a failed motor | | Smell of burning | Switch it off, leave it off and call for service |

Do not do these

  • Do not keep resetting a breaker or GFCI that trips again. Each reset energizes the fault.
  • Do not spray or wipe down live equipment to dry it out.
  • Do not open junction boxes or timer enclosures while standing in water or while the pad is wet.
  • Do not bypass a GFCI to get the pump running. The protection is there for a reason.
  • Do not assume the pump is the problem. Many storm outages are in the supply or the controls.

After power is back

Once the breaker and GFCI hold and the equipment runs, watch the pad for the next day or two. Check that the timer kept its schedule, that the pump primes and moves water normally, and that no breaker trips on the next afternoon rain. A fault that comes back after the first storm usually means water is still getting into a box or fitting, and it should be inspected before the next round of weather.

Keep a simple storm log

Note the date, what went out, what you reset and what happened. If the same circuit goes out after every storm, that pattern tells an electrician more than a single outage does, and it points toward repairs such as resealing boxes, replacing worn fittings or adding surge protection.

Need Pool Electrical Repair in Clermont, FL?

Talk to a local pool electrical repair company serving Clermont and nearby neighborhoods.

Call now Get help